Shims

Discussions on How to Service Your Mitchell Reel and more...
Post Reply
User avatar
RandallHeide
Posts: 2
Joined: Sun Mar 26, 2023 5:32 pm

Shims

Post by RandallHeide »

Are there replacement or alternative shims available?


User avatar
GreatLaker
Posts: 232
Joined: Sat Jun 12, 2021 1:05 am

Re: Shims

Post by GreatLaker »

RandallHeide, :text-welcomeconfetti: Welcome to the Mitchell Reel Museum (MRM)!

You can find shims for sale on the big auction site. Most shims for the Mitchell 300 come in 3 sizes.
Kind Regards,
Bill :D


User avatar
RandallHeide
Posts: 2
Joined: Sun Mar 26, 2023 5:32 pm

Re: Shims

Post by RandallHeide »

GreatLaker wrote: Fri Mar 31, 2023 7:09 pm RandallHeide, :text-welcomeconfetti: Welcome to the Mitchell Reel Museum (MRM)!

You can find shims for sale on the big auction site. Most shims for the Mitchell 300 come in 3 sizes.
Kind Regards,
Bill :D
Thank you Sir!!!


User avatar
GreatLaker
Posts: 232
Joined: Sat Jun 12, 2021 1:05 am

Re: Shims

Post by GreatLaker »

RandallHeide,
If you do a search under shims you can find more information on shims from former posts.
Here is a good one to check out.

https://mitchellreelmuseum.com/forum/vi ... 50e06#p354

Kind Regards,
Bill :D


User avatar
Bailarm
Posts: 124
Joined: Sun Jun 13, 2021 3:16 pm
Location: Surrey UK
Contact:

Re: Shims

Post by Bailarm »

Thanks for the link, Bill. That's enabled me to search for some main gear shims 81-035 that are so hard to find now. It turns out European M7 shim washers suit, but with a slightly larger OD at 13mm, not 10. and ID at 7mm, not 6.579mm. They are available in 0.001, 0.003 and 0.005mm thicknesses, so good for anyone in Europe.

:text-bravo:


}<)))'> Bailarm
User avatar
Bailarm
Posts: 124
Joined: Sun Jun 13, 2021 3:16 pm
Location: Surrey UK
Contact:

Re: Shims

Post by Bailarm »

These M7 shims have turned up already. I was concerned that the outside diameter ( OD) might be too large at 13mm but it turns out that the size of main gear centre boss they would sit next to, so they should be fine.

You can get them from this eBay seller:

https://www.ebay.co.uk/itm/224326415431 ... SwKKJhp-sM


}<)))'> Bailarm
User avatar
GreatLaker
Posts: 232
Joined: Sat Jun 12, 2021 1:05 am

Re: Shims

Post by GreatLaker »

Nobby,
Thanks for the link regarding the shims. You should remember that those shims are made out of steel which can rust. The Mitchell shims are all made out of brass so no chance of rust, just saying.
Kind Regards,
Bill :D


User avatar
Bailarm
Posts: 124
Joined: Sun Jun 13, 2021 3:16 pm
Location: Surrey UK
Contact:

Re: Shims

Post by Bailarm »

Good point Bill. I was once fishing when as serious storm went over Salisbury Plain. As well as the cane rod needing drying the reel got water in it too...good job I checked.

There's no source for these shims in the UK and the only ones left seem to be in France and the US...and somewhat expensive if you're servicing a lot of reels.

I have found another supplier, even cheaper, who's shims are in stainless steel.

https://springfasteners.co.uk/?s=shim+w ... A..*_up*MQ..

Bit of a slow site.


Din 988 is actually a worldwide standard for stainless steel it seems.


}<)))'> Bailarm
Post Reply